BROADCOM ADVANCED CONTROL SUITE 2 10.4 DRIVER DOWNLOAD

MAC control frames with no pause command. Set the probe interval the number of seconds between each retransmission of a link packet to the probe target and the maximum number of probe retries the number of consecutively missed responses from a probe target before a failover is triggered. It is recommended to accept the default values for Probe interval the number of seconds between each retransmission of a link packet to the probe target and Probe maximum retries the number of consecutively missed responses from a probe target before a failover is triggered. If you disable a virtual team and later want to reenable it, you must first disable and reenable all team members before you reenable the virtual team. This information is displayed only when there is a team see Configuring Teaming. The standby member does not actively send and receive normal network traffic while other adapters on the team are active.

Uploader: Kikora
Date Added: 9 September 2016
File Size: 67.39 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 10446
Price: Free* [*Free Regsitration Required]

To perform a silent install or upgrade from within the installer source folder.

The valid number is ranged from 2 – The Standby Member field is used to permit the selection of one of the team members to handle traffic, should all members in the Load Balance Member list fail failover. The Jumbo Frames property allows the network adapter to transmit and receive oversized Ethernet frames that are greater than bytes, but less than bytes in length. Suote test fails if an erroneous value is read back.

  DIGIMAX D53 CAMERA DRIVER

The number of bits that the bus can transfer at a single time to and from the adapter. The physical layer chip is used to control the electrical signals on the wire and for configuring network speed. By default, advancdd property is set to Enable. Installs the Simple Network Management Protocol subagent.

Using Broadcom Advanced Control Suite 2: Broadcom NetXtreme II™ Network Adapter User Guide

This value can never be 0. Do not forget to check with our site as often as possible in order to stay on the latest drivers, software and games booth. From the Suits menu, click Team Restore. For further information regarding teaming protocols, see “Teaming” in your Broadcom network adapter user guide.

Broadcom Advanced Control Suite 2: Broadcom NetXtreme® 57XX User Guide

Otherwise, problems may occur. The benefit of this approach is that it enables load balancing and failover. A count of frames that were successfully transmitted as indicated by the transmit status Transmit OK to the broadcast address. Consequently, the adapter that was initially designated a load balance member remains in an inactive state and becomes the new ocntrol member.

Click Cancel to discard your settings and exit the wizard.

The potentially available properties and their respective settings are described below. If an adapter is not fully supported, you can click List All Supported Adapters to display a list of fully supported adapters.

Click the name of the file to be restored, and then click Open.

Broadcom Advanced Control Suite 2 9.7.0.1 For Windows All

To view this information for any team member adapter, click the name of the adapter. The subsystem vendor ID. This test verifies the read and write capabilities of the registers of the physical layer PHY.

  GPIB - USB-HS DRIVER

A count of frames that were successfully received and are directed to a broadcast group address. This condition does not apply contrlo an adapter that is a standby member of a team.

The version of boot code 2. This mode does not provide link aggregation control protocol LACP or marker protocol support. Large Advancev Offload prevents an upper level protocol such as TCP from breaking a large data packet into a series of smaller packets with headers appended to them.

If you do broaadcom want to contrlo LiveLink, click Noand click Next. Team names must be unique. Broadcom Advanced Control Suite 2 9. This minimizes the downtime due to spanning tree loop determination when failing over. The network adapter may not function if the network is not configured to operate at the same mode. Click OK or Apply to save the changes. For a two-port adapter, the function number for the first port is 0, and the function number for the second port is 1.

A count of directed data frames that are successfully received.